Carbon blades for V-Force 3R reed box 3P412M

<p>V-Force 3 reed box, Kawasaki SXR-800, 03-11 V3150-794-2</p>

V-FORCE

<p>To Fit The Derbi Variant 50,Fits All Years.</p> <p>This Reed Valve Had Double The Set Of Reeds Compared To Std Reed Valve, This Gives The More Flow Though The Inlet System Which In Turn Gives You Better Throttle Response And More Punch Out Of The Corner.</p> <p>Comes complete with A D.26mm (D.35mm ext) inlet manifold to fit 24/28 carbs.</p>

ITALKIT

<p>Polini carbon blades for 213.0036 / 42/44 (2130526) 213.0526</p>

POLINI

<p>Films for reed box V-Force 3 V352A / V354A 3P352FG</p>

V-FORCE

<p>Set of two original replacement gaskets for the VForce reed valve system by Moto Tassinari.</p> <p>Please note, all gasket part numbers that end with "-K" include two gaskets.</p> <p>Place one gasket on each side of the VForce manifold during installation.</p> <p>One "-K" set is enough gaskets for one reed valve. If you have a twin, you will need to order two "-K" sets to have the required four gaskets.</p>

V-FORCE

<p>Voca reed valve spacer Yamaha DT 50/80 LC, TZR 80 LC red</p> <ul> <li>Int: 46x44</li> <li>Ext: 72x62</li> </ul> <p></p>

VOCA RACING

<p>V-Force 3 Reed Valve, 2002 Honda CR250 V315A</p>

V-FORCE

<p>Polini Evolution Reed Valve Box, with a wider intake diameter for better cylinder filling. It features a metallized surface.</p> <p>The reed box comes with carbon reeds.</p> <p>The Venturi of the reed box is designed with an optimized angle and flow section for a better air-fuel mixture.</p> <p>It improves gas flow, providing a quicker throttle response.</p> <p>It replaces the original reed box without the need to change any other parts. Essential for larger carburetors and for bikes with bigger cylinders. Highly recommended for stock bikes, as the original reeds tend to lose their efficiency over time.</p> <p></p>

POLINI

<p>Blades for KTM / HUSQVARNA V-Force 4R reed box 4P672H</p>

V-FORCE

<p>Italkit has developed a new reed valve cage for KTM SX65 with a new cage especially designed for this engine.</p> <p>Composed of 4 special reed petals and 4 "balestrinos" in charge of regulating the pressure on high revolutions, due to this kit brings rubber pipe manifold with diffuser integrated for carburetor Ø24 mm. Throughout tests carried out on bench test and later tested in racetrack, it has gotten a power increment specially on high revolutions, where the engine appreciates this performance improvement, with a faster increment of rpm, providing higher top speed very appreciated for riders.</p>

ITALKIT

<span>For Sport valve</span>

MALOSSI

<p><span>YAMAHA RD 350 / BANSHEE VFORCE 4 Reed Valve</span></p>

V-FORCE

<span>for original valve</span>

MALOSSI

<p>The VForce reed valve system by Moto Tassinari has been the reed valve system of choice by anyone serious about two-stroke engine performance for the last 10+ years. The simple premise of the VForce4 reed valve system is to increase engine power and throttle response by increasing the efficiency over a conventional reed valve design.</p> <ul style="list-style-type:disc;"> <li>SX125SX 2016 - 2020</li> <li>SX250 2017 - 2020</li> <li>EXC300 2017 - 2018</li> <li>EXC300 TPI 2018 - 2020</li> </ul> <p>Moto Tassinari / V-Force 4 V4R26</p>

V-FORCE

<p>Reed petals Italkit Minarelli MR 80/Rieju RST 80/Yamaha TZR 125</p>

ITALKIT

<p>Polini Reed Box, Big Valve Kymco Sniper (213.0042) 213.0042</p>

POLINI